The FAB4300 Module is a Unity Buffer Amplifier Module, utilizing either a PDIP8 chip, or a Discrete OpAmp.

It has a single-ended input, and a single-ended output. The output of the OpAmp is connected back to it’s inverting input (IN-), while the input signal is applied to the non-inverting input (IN+).  The output of the OpAmp basically follows whatever is the input signal applied to IN+, thus  it’s named a voltage follower.

While the FAB4300 does not offer any amplification to the input signal, it serves a very important function. The input impedance of the FAB4300 Module is very high, meaning that the FAB4300 does not load down the signal source. At the same token, the output impedance of the FAB4300 Module is very low and thus it can drive loads very efficiently without any apparent loss in signal. You can say the FAB4300 acts like an impedance bridging circuit.

Continue Reading…

I did a quick test just to see if all the FAB Modules work and play well together.  I’m very pleased with the results…. The modules were quiet, and even with a long signal chain as you can see in the picture, there was hardly any noise I could hear.  (For testing, I hooked up a condenser microphone and connected the outputs to a KRK RP8 8″ Monitors. No humming, no RF noise, nothing.)

Everything works… the logic control Phantom Power, -20dB Pad, Polarity Reverse, and the +6dB Boost (1:2 Transformer Ratio).  To get the FAB4312 Non-Inverting Amplifier working, I hooked up a small 10K potentiometer so I can adjust gain.  For now, I just used a jumper and connected the Phantom Power Logic control inputs directly to a spare V+ terminal on the FAB1215 PSU module.

Continue Reading…

This is our FAB4312 Non-Inverting Amplifier Module.  You can use any single opamp, 8-pin PDIP package like an LME49710, NE5534 or equivalent. It also features Mill-max sockets if you want to mount a 2520-style discrete opamp, like our DOA-12, DOA-17, 990C, API 2520, or compatible discrete opamp.

A trimmer is also provided to let you adjust DC offset to zero volts (0V). A 2-pin header is provided for connection of your gain control potentiometer (or selector switch, or digital potentiometer, or switched resistor ladder network).  In the future, we’ll be providing FAB modules that will offer these different options for controlling the gain of your amplifier.

Continue Reading…

The DOA-12 is a high-performance, discrete operational amplifier well suited for demanding audio applications due to it’s low noise, high slew rate, high gain capability, high output capability, and operation over a wide range of power supply voltages. It uses the standard discrete opamp 2520/990 footprint… a roughly 1”x1” device with (6) pins, a format commonly found and used in pro-audio gear.

Running at +/-24Volts supply voltage, the DOA-12 is capable of reaching +26dBu output (loaded with a 600:600 output transformer). Running at a slightly lower +/-18Volts supply voltage, the DOA-12 still achieves an impressive +24dBu maximum output.

Continue Reading…

The DOA-17 is our modern remake of a vintage discrete op amp design, using modern low-noise components and improved layout. It uses the standard discrete opamp 2520/990 footprint… a roughly 1”x1” device with (6) pins, a format commonly found and used in pro-audio gear.

Running at +/-18Volts supply voltage, the DOA-12 is capable of reaching +23dBu output (loaded with a 600:600 output transformer). If one uses the DOA-17 to drive an output transformer wired for 1:2, it is possible to create high-performance preamplifiers capable of reaching +29dBu output!

Each DOA-17 is designed and tested to be stable, and oscillation-free even at maximum output levels and gain settings due to careful selection of components, efficient PCB layout, design, and construction.

Continue Reading…